If the tyre pressure light won’t go off, work out first whether it is flashing or steady. A light that flashes on startup and then stays on is reporting a fault in the monitoring system, and no amount of inflating will clear it. A steady light that persists after you have corrected the pressures usually means a leak you have not found, a reset that has not been done, or a sensor that has stopped reporting.
The usual causes, in the order worth checking:
- A tyre still below the threshold
- A reset never carried out
- A dead sensor battery
- A sensor damaged during a tyre change
- A wheel without a sensor fitted
- A slow leak refilling the gap
Check What the Light Is Doing
Spend one minute on this before anything else, because it splits the problem in two.
Start the engine and watch the light. Every warning lamp illuminates briefly during the bulb check, which is normal. What matters is what happens after.
Flashes for a while, then stays solid. This is the standard signal for a TPMS malfunction. The car cannot read one or more sensors. Your tyres may be perfectly inflated.
Comes straight on and stays on. The system is reporting low pressure. Something is either still low or still leaking.
Chasing a flashing light with a foot pump is the most common wasted afternoon in this whole topic.
You Have Already Inflated Them
If you topped the tyres up and the light stayed on, there are a handful of specific reasons, and they are covered in detail in why is my tyre pressure light still on after filling tyres.
The short version is that one of three things is usually true. The pressures were set against the wrong figure, the system needs a reset or a drive cycle to clear, or one tyre is leaking fast enough to drop back below the threshold before you got home.
The Reset Nobody Mentions
Indirect systems need telling that you have fixed the problem. They do not measure pressure, so they have nothing to re-measure.
After inflating or changing a tyre on an indirect system, the reset is usually a button in the glovebox or footwell, or a menu item in the driver display. The car then relearns the correct rolling diameters over a short drive.
Direct systems normally clear on their own once pressures are correct and the car has been driven for a few minutes, because the sensors transmit new readings. Where one does not, the sensor is the suspect rather than the tyre.
Your handbook has the exact procedure for your car, and it varies more between manufacturers than you would expect. The related system warning and how it differs is covered in how to fix service tyre monitor system.
Dead Sensor Batteries
This is the single most common cause of a light that will not clear on an older car, and it catches people out because nothing is wrong with the tyre.
Direct TPMS sensors run on sealed batteries lasting roughly five to ten years. The battery is not separately replaceable, so a flat one means a new sensor.
Three things follow from that:
- Sensors tend to fail around the same time, since they were all fitted together. One failure often means the others are close behind.
- Replacing all four at once is worth considering on a car over about eight years old, rather than paying a call-out each time another dies.
- Age, not mileage, is what kills them. A low-mileage car is not exempt.
A TPMS tool reads battery status directly, so this takes minutes to confirm rather than being a guess.
Damage During a Tyre Change
Sensors sit on the valve inside the wheel, which is exactly where a tyre machine works.
A sensor can be cracked, snapped or knocked out of alignment during fitting, and the light appears a day or two later. It can also simply not have been relearned to the car after the new tyre went on, which looks identical from the driver’s seat.
If the light appeared shortly after a tyre was changed, say so when you book the diagnosis. It narrows the cause immediately. The fitting process and where sensors sit in it is described in how to change a tyre on a rim.
A Wheel With No Sensor In It
Easy to overlook, and it produces a permanent fault light.
- A space saver spare fitted after a puncture usually has no sensor, so the system reports a missing wheel.
- A winter wheel set bought separately often comes without sensors unless you specified them.
- A replacement wheel after pothole or kerb damage may have been fitted without transferring the sensor across.
In each case the light is correct. The system genuinely cannot find a sensor, and the fix is fitting and programming one.
The Leak You Have Not Found
Where the light keeps returning days after each top-up, the tyre is losing air somewhere.
Not every leak is a nail in the tread. The common ones are a corroded valve stem, a poor seal between tyre and rim after a kerb impact, or a cracked alloy. These lose air steadily and leave nothing visible on the tread.
A fitter finds these by removing the wheel and submerging it, which is the only reliable method. Once located, whether it can be repaired depends on where it sits, and those rules are in when can a puncture be repaired. Driving on it in the meantime is covered in can you drive on a slow puncture.
Does It Matter for the MOT?
Yes, and this is the part that turns a nuisance into a cost.
TPMS has been checked at MOT since January 2015 on cars first used on or after 1 January 2012. A system that is clearly not working, or a lamp indicating a system fault, is a major defect and a fail.
The distinction matters. A lamp on because a tyre is genuinely low is not a system fault, and the tester is not meant to reject the car for it. A lamp indicating the TPMS itself has failed is. So the flashing-then-steady light is the one that fails you.
Get It Read Rather Than Guessed
Everything above is diagnosable in minutes with a TPMS tool, which reads each sensor’s ID, pressure reading and battery condition.
Without one you are working by elimination, and the usual outcome is paying for a tyre that was never the problem. Run-flats complicate it further, since they hide underinflation well, and the trade-offs there are covered in how to choose the right tyres: budget vs premium vs run-flats. What a mobile visit involves is set out in what to expect from mobile tyre fitting.
Frequently Asked Questions
Why is my tyre pressure light still on when my tyres are fine?
Most likely a TPMS fault rather than a pressure problem, shown by the light flashing before it stays on. Dead sensor batteries are the usual cause on older cars.
How do I reset the tyre pressure light?
Indirect systems use a reset button in the glovebox or footwell, or a menu option, followed by a short drive. Direct systems normally clear themselves once pressures are correct.
How long does it take for the tyre pressure light to go off?
Usually within a few minutes of driving after the pressures are corrected. If it is still on after a full journey, something other than pressure is causing it.
Can a TPMS sensor battery be replaced on its own?
No. The battery is sealed inside the sensor, so a flat one means replacing the whole sensor, typically after five to ten years of service.
Will a tyre pressure light fail an MOT?
A lamp indicating a TPMS system fault is a major defect and a fail on cars first used from 1 January 2012. A lamp on simply because a tyre is low should not be.
Mobile Tyres Services reads the system with a TPMS tool before touching anything, so you find out whether it is a sensor, a reset or a leak rather than paying to replace parts by elimination. We cover sensor replacement, programming and relearning at your home or workplace.
If it turns out to be a slow leak, we repair or replace on the same visit. Call 07448162740 and we will get the light off.